050-0113 Two Rotor Latch Single-Position Intertrip

This two rotor latch is a sub-platform to the TriMark proven 050-0100 series latch and is designed for medium to heavy-duty applications for on or off highway entrance doors, compartments and access panels. It features an internal trip mechanism for applications where it is desirable to have the release mechanism in-line with the latch and a single position latch.

DESIGNED FOR:

  • Door thicknesses of 1-7/8" or greater (47.6mm)
  • Door weights of 50-200 lbs. (23-91 kg)
  • Door seal pressures of 50-150 lbs. (23-68 kg)(suggested for best results)
  • Use with TriMark 070-0200 Striker Bolt

AVAILABLE:

  • In left or right hand configurations
  • With (4) 1/4-20 UNC, M6 x 1 threaded axles or .286" (7.3mm) diameter "thru" axles
  • With trip lever options.

FINISH:

  • Zinc plated, clear chromate steel components

MATERIAL:

  • Internal latch components: heat treated, smooth edge stamped steel
  • Case halves: high strength steel
  • Springs: non-corrosive stainless steel

INSTALLATION:

  • (4) 1/4-20 UNC grade 5, M6 x 1 class 8.8 or better fasteners are required (not included).
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)
  • Fastener mounting holes diameter should not exceed .281" (7.1 mm)

INTERNAL LUBRICATION:

  • Oven-cured dry lubricant is applied at factory on all critical moving parts

STRIKER INSTALLATION:

  • Install striker bolt in door frame
  • Close door carefully and check for interference between head of striker bolt and latch components
  • Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
  • Adjust striker bolt vertically so door is not guided upward or downward while being closed
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust striker bolt
  • After installation, check door alignment and door seal pressures

CAUTION: Single position rotary latches do not comply with FMVSS 206 (ECE R11) requirements.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0113 Two Rotor Latch Single-Position Intertrip

  • Agricultural Tractor / Combine

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Bus / Motorcoach / Mass Transit

    Access Panels

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Construction - Heavy Earthmoving

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Construction - Lifting and Material Handling

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Construction - Light Earthmoving

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Access Panels

    Exterior Storage Compartments


  • Heavy Truck / Sleeper Cabs

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Storage Compartments

    Tool Boxes


  • Industrial Enclosure/Cabinet

    Access Panels/Cabinet Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Engine Compartments / Hoods


  • Replicars / Kit Cars

    Engine Compartments / Hoods


  • Step Van / Walk-in Vans / Delivery Vehicle

    Exterior Storage Compartments

    Tool Boxes


  • Trailers - Ranch / Farm / Cargo / Utility

    Access Panels

    Exterior Storage Compartments


  • Travel Trailer / 5th Wheel

    Baggage Doors


  • Utility Bodies / Wreckers / Specialty Truck

    Exterior Storage Compartments

    Tool Boxes


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingMountingActuationCatch SpringInternal Trip Lever SpringFinishLatch Plate CutoutsStatus CodeSample RequestCAD Drawing
0500113-1-01-1636801CNTD-01-00-015-0316623-01 Right Hand 1/4-20 UNC Catch release (16368-01) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate end cutoutA/A
0500113-1-01-3319601LVRR-02-01-015-0833197-01 Right Hand 1/4-20 UNC Lever release (33196-01) Heavy Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge and small end cutoutsA/A
0500113-1-02-1156216CTHD-01-00-015-0113284-03 Right Hand .286 (7.3mm) Diameter Through Axles Threaded end on catch, Threaded 1/4-20 (11562-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate edge cutoutA/A
0500113-1-02-1636801CNTD-01-00-015-0416369-01 Right Hand .286 (7.3mm) Diameter Through Axles Catch release (16368-01) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate edge and end cutoutsA/A
0500113-1-02-2189501LVHL-01-01-015-1021782-01 Right Hand .286 (7.3mm) Diameter Through Axles Lever release, .204" (5.18mm) hole (14498-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge and end cutoutsA/A
0500113-1-02-2506101LVRR-01-02-015-0521530-01 Right Hand .286 (7.3mm) Diameter Through Axles Lever release (25061-01) Normal Duty Catch Spring Heavy Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-1-06-1256716CTHD-01-00-015-0117937-01 Right Hand M6 X 1.0 Threaded end on catch, Threaded M6X1 (12567-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate edge cutoutA/A
0500113-1-06-1766402LVRR-01-03-015-0517665-01 Right Hand M6 X 1.0 Lever release (17664-02) Normal Duty Catch Spring High Stress Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-1-06-2190301LVHL-01-02-015-0616961-01 Right Hand M6 X 1.0 Lever release, .265" (6.73mm) hole (21903-01) Normal Duty Catch Spring Heavy Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge cutoutA/A
0500113-1-06-2194601LVSL-02-01-015-1231170-01 Right Hand M6 X 1.0 Lever release, .370" (9.4mm) X .3531" (13.5mm) slot (21946-01) Heavy Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutoutsA/A
0500113-1-06-2968101LLNK-01-01-015-1231120-01 Right Hand M6 X 1.0 Lever release, with link , .285" (7.25mm) hole (29681-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutoutsA/A
0500113-1-06-3611501LWES-01-01-015-1236116-01 Right Hand M6 X 1.0 Lever release with extension spring return, .276" (7mm) hole (36115-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutoutsA/A
0500113-1-06-3611501LWES-01-01-015-2141378-02 Right Hand M6 X 1.0 Lever release with extension spring return, .276" (7mm) hole (36115-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutouts/wire harnessA/A
0500113-2-01-2787701LVRR-02-01-015-1133195-01 Left Hand 1/4-20 UNC Lever release (27877-01) Heavy Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate small end cutoutA/A
0500113-2-01-8106916CNTD-01-00-015-0316622-01 Left Hand 1/4-20 UNC Catch release (81069-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate end cutoutA/A
0500113-2-01-8111016CNTD-01-00-015-0315372-01 Left Hand 1/4-20 UNC Catch release (81110-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate end cutoutA/A
0500113-2-01-8111016CNTD-01-00-015-0920857-01 Left Hand 1/4-20 UNC Catch release (81110-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate edge and end cutouts + Back plate edge and end cutoutsA/A
0500113-2-02-1156216CTHD-01-00-015-0113283-03 Left Hand .286 (7.3mm) Diameter Through Axles Threaded end on catch, Threaded 1/4-20 (11562-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate edge cutoutA/A
0500113-2-02-2189601LVHL-01-01-015-0516826-01 Left Hand .286 (7.3mm) Diameter Through Axles Lever release, .204" (5.18mm) hole (21896-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-02-2506201LVRR-01-02-015-0521529-01 Left Hand .286 (7.3mm) Diameter Through Axles Lever release (25062-01) Normal Duty Catch Spring Heavy Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-06-1195216CWKB-01-00-015-0211938-01 Left Hand M6 X 1.0 Catch release, with knob (11952-16) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Front plate cutout on rotor edgeA/A
0500113-2-06-2190601LVRR-01-01-015-0819596-01 Left Hand M6 X 1.0 Lever release (21906-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge and small end cutoutsA/A
0500113-2-06-2190701LVRR-01-01-015-0718096-02 Left Hand M6 X 1.0 Lever release (21907-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate small end cutout + Back plate small end cutout A/CP
0500113-2-06-2191801LVHL-01-01-015-0522537-01 Left Hand M6 X 1.0 Lever release, .207" (5.25mm) hole (21918-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-06-2253601LVHL-01-01-015-0521451-01 Left Hand M6 X 1.0 Lever release, .207" (5.25mm) hole (22536-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-06-2968101LLNK-01-01-015-1229679-01 Left Hand M6 X 1.0 Lever release, with link , .285" (7.25mm) hole (29681-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutoutsA/A
0500113-2-06-3398601LVHL-01-01-015-0533985-01 Left Hand M6 X 1.0 Lever release, .276" (7mm) hole (33986-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-06-3874401LVHL-01-01-015-0538745-01 Left Hand M6 X 1.0 Lever release, .276" (7mm) hole (38744-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Back plate edge cutoutA/A
0500113-2-06-4098901LVHL-01-01-015-1240990-02 Left Hand M6 X 1.0 Lever release, .197" (5mm) hole (40989-01) Normal Duty Catch Spring Normal Duty Internal Trip Lever Spring Zinc Plate/Clear Chromate Front plate edge cutout + Back plate edge and small end cutoutsA/A
500113-1-06-5027601CLCR-01-00-015-2050278-01 Right Hand M6 X 1.0 Catch with release through latch cutout (50276-01) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Back plate cutouts on both rotor edgesA/A
500113-2-06-5027501CLCR-01-00-015-2050277-01 Left Hand M6 X 1.0 Catch release with release through latch cutout (50275-01) Normal Duty Catch Spring None Zinc Plate/Clear Chromate Back plate cutouts on both rotor edgesA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale