• Home
  • Products  /  Accessories  /  
  • 070-0201 .550 “ (13.9mm) Diameter Striker Bolt and Optional Guard

070-0201 .550 “ (13.9mm) Diameter Striker Bolt and Optional Guard

Designed as a companion part for use with TriMark's single rotor latches and cage nuts that requires a .550" (13.9mm) diameter striker bolt. It is available in a variety of lengths with several drive details and mounting thread choices.

 Installation

  • Torque 7/16-14 UNC-24 to 56 ft-lbs minimum depending upon surface conditions

Material

  • Typical materials include AISI 4147 or AISI C10B21 steel (or equivalent), heat treated to TriMark ES-141

Finish

  • Zinc plated with clear chromate

Caution: TriMark striker bolts are designed and tested to meet or exceed FMVSS 206 (ECE R11) safety requirements only when used with TriMark's corresponding FMVSS 206 (ECE R11) compliant latches. Note that some of the longer striker bolts have diminished load values in certain latch families. Please check with TriMark Engineering before finalizing your striker selection requiring FMVSS 206 (ECE R11) compliance.

Latch & Striker Installation

  • Install striker bolt in door frame
  • Close door carefully and check for interference between head of striker bolt and latch components
  • Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
  • Adjust striker bolt vertically so door is not guided upward or downward while being closed
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust striker bolt
  • After installation, check door alignment and door seal pressures

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-0201 .550 “ (13.9mm) Diameter Striker Bolt and Optional Guard

Please specify search criteria:


CompareCatalog NumberTriMark NumberShoulder DiameterThread SizeInstalled LengthThread LengthDrive Detail Internal or ExternalWasher Dia. X ThicknessStriker GuardTypePackaging, Part MarkingStatus CodeSample RequestCAD Drawing
0700201-00-00-174-0000-00-00-1-06-1122137-01 NA None 1.74 NA NA NA Yes Guard Individually bagged, no part markingA/A
0700201-05-00-140-0000-13-00-0-07-0737972-01 0.55 None 1.40 NA Welded on Plate NA No Bolt fastened to 37971-01 plate, (2) 19mm holes, 53.02mm X 50mm, black e-coat Standard packaging, date code on plateA/A
0700201-05-00-156-0000-04-00-1-04-1429019-01 0.55 None 1.56 NA 0.312 Internal NA Yes Bolt fastened to 29020-01 plate, (2) 14mm X 19mm slots, 30.5mm X 50mm Standard packaging, customer part number and date code on plateA/A
0700201-05-01-087-0827-04-07-0-01-0131985-02 0.55 7/16-14 UNC-2A 0.87 0.827 0.312 Internal 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-091-0788-04-07-0-01-0131985-01 0.55 7/16-14 UNC-2A 0.91 0.788 0.312 Internal 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-091-0788-11-07-0-01-0132243-01 0.55 7/16-14 UNC-2A 0.91 0.788 T-50 - 6 Lobe 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-091-0788-11-07-0-01-0332081-01 0.55 7/16-14 UNC-2A 0.91 0.788 T-50 - 6 Lobe 1.10 X 0.11 No Bolt, washer, o-ring Customer returnable, customer part number on washerA/A
0700201-05-01-091-0788-11-07-0-01-0632081-02 0.55 7/16-14 UNC-2A 0.91 0.788 T-50 - 6 Lobe 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, customer part number on washerA/A
0700201-05-01-095-0749-11-07-0-01-0119354-01 0.55 7/16-14 UNC-2A 0.95 0.749 T-50 - 6 Lobe 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-096-0743-11-11-041858-01 0.550 7/16-14 UNC-2A 0.96 0.743 T-50 - 6 Lobe 1.10 X 0.15 Grip Teeth No  A/A
0700201-05-01-096-1395-04-07-0-01-0128565-01 0.55 7/16-14 UNC-2A 0.96 1.395 0.312 Internal 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-098-0748-04-09-0-01-0111614-16 0.55 7/16-14 UNC-2A 0.98 0.748 0.312 Internal 1.10 X 0.13 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-100-0732-04-10-0-01-0139381-01 0.55 7/16-14 UNC-2A 1 0.732 0.312 Internal 1.10 X 0.15 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-100-0940-04-09-0-01-0122114-01 0.55 7/16-14 UNC-2A 1 0.940 0.312 Internal 1.10 X 0.13 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-100-1126-04-09-0-01-0115998-01 0.55 7/16-14 UNC-2A 1 1.126 0.312 Internal 1.10 X 0.13 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-102-1110-04-11-0-01-0115998-02 0.55 7/16-14 UNC-2A 1.02 1.110 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-119-0732-04-11-0-01-0118285-01 0.55 7/16-14 UNC-2A 1.19 0.732 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-121-0749-04-08-0-01-0131062-01 0.55 7/16-14 UNC-2A 1.21 0.749 0.312 Internal 1.10 X 0.11 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-126-0704-04-11-0-01-0120693-01 0.55 7/16-14 UNC-2A 1.26 0.704 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-126-0704-04-11-0-01-0220693-02 0.55 7/16-14 UNC-2A 1.26 0.704 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 max per box, labeled for export, no part markingA/A
0700201-05-01-145-0795-04-07-0-01-0136599-01 0.55 7/16-14 UNC-2A 1.45 0.795 0.312 Internal 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-145-0995-04-07-0-01-0128619-01 0.55 7/16-14 UNC-2A 1.45 0.995 0.312 Internal 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-145-1421-11-07-0-01-0124082-01 0.55 7/16-14 UNC-2A 1.45 1.421 T-50 - 6 Lobe 1.10 X 0.11 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-01-147-0966-04-15-0-01-0137401-01 0.55 7/16-14 UNC-2A 1.47 0.966 0.312 Internal 1.50 X 0.13 No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-02-120-0850-07-11-0-01-0112475-16 0.55 1/2-13 UNC-2A 1.2 0.85 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-02-120-0850-07-11-0-01-0212475-01 0.55 1/2-13 UNC-2A 1.2 0.85 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 max per box, labeled for export, no part markingA/A
0700201-05-02-120-1100-07-11-0-01-0429847-01 0.55 1/2-13 UNC-2A 1.2 1.100 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 per bag, no part markingA/A
0700201-05-02-120-1100-07-11-0-01-0529847-02 0.55 1/2-13 UNC-2A 1.2 1.100 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 per bag, labeled for export, no part markingA/A
0700201-05-02-157-0795-07-11-0-01-0112490-16 0.55 1/2-13 UNC-2A 1.57 0.795 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-100-0732-07-11-0-01-0111807-16 0.55 M12 X 1.75-6g 1 0.732 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-100-0890-07-11-0-01-0122363-01 0.55 M12 X 1.75-6g 1 0.89 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-110-0628-04-09-1-01-0134085-01 0.55 M12 X 1.75-6g 1.10 0.628 0.312 Internal 1.10 X 0.13 Yes Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-126-0704-04-11-0-01-0129820-01 0.55 M12 X 1.75-6g 1.26 0.704 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-126-0704-04-11-0-01-0229820-02 0.55 M12 X 1.75-6g 1.26 0.704 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 max per box, labeled for export, no part markingA/A
0700201-05-06-150-0700-07-11-0-01-0114235-01 0.55 M12 X 1.75-6g 1.5 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-150-0700-07-11-0-10-1223328-01 0.55 M12 X 1.75-6g 1.5 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring assembled to LH cam assembly, 40mm offset Standard, date code on camA/A
0700201-05-06-150-0700-07-11-0-11-1223332-01 0.55 M12 X 1.75-6g 1.5 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring assembled to RH cam assembly, 40mm offset Standard, date code on camA/A
0700201-05-06-150-1110-07-11-0-01-0117484-01 0.55 M12 X 1.75-6g 1.5 1.110 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-158-1035-07-11-1-05-0132277-01 0.55 M12 X 1.75-6g 1.58 1.035 0.875 External 1.10 X 0.15 Grip Teeth Yes Bolt, washer, lock nut Standard packaging, no part markingA/A
0700201-05-06-167-1011-07-11-0-01-0126576-01 0.55 M12 X 1.75-6g 1.67 1.011 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-183-0700-07-11-0-01-0121789-01 0.55 M12 X 1.75-6g 1.83 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-183-0700-07-11-0-01-0221789-02 0.55 M12 X 1.75-6g 1.83 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 max per box, labeled for export, no part markingA/A
0700201-05-06-183-0700-07-11-0-12-0829638-01 0.55 M12 X 1.75-6g 1.83 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring assembled to cam assembly, 21mm offset Standard packaging, part number and date code on plateA/A
0700201-05-06-183-0700-07-11-0-15-0832189-01 0.55 M12 X 1.75-6g 1.83 0.700 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring assembled to cam assembly, 83mm offset Standard packaging, part number and date code on plateA/A
0700201-05-06-183-0953-07-11-0-01-0132630-01 0.55 M12 X 1.75-6g 1.83 0.953 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Standard packaging, no part markingA/A
0700201-05-06-183-1200-07-11-0-01-0224581-01 0.55 M12 X 1.75-6g 1.83 1.200 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special packaging, 50 max per box, labeled for export, no part markingA/A
0700201-05-10-149-0638-04-10-0-01-0138375-01 0.55 M12 X 1.75-6H 1.49 0.638 0.312 Internal 1.10 X 0.15 No Bolt, washer, o-ring Standard packaging, no part markingA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale