• Home
  • Products  /  Accessories  /  
  • 070-0200 .675" (17.1mm) Diameter Striker Bolt and Optional Guard

070-0200 .675" (17.1mm) Diameter Striker Bolt and Optional Guard

Designed as a companion part for use with TriMark's two rotor latches and cage nuts that requires a .675" (17.1mm) diameter striker bolt and compliance to FMVSS 206 (ECE R11). It is available in a variety of lengths with several drive details and mounting thread choices.

Material

  • Typical materials include AISI 4140 and AISI C10B21 steel (or equivalent), heat treated to TriMark ES-141

Installation

  • Torque 7/16-14 UNC-2A to 56 ft-lbs minimum depending upon surface conditions
  • Torque 1/2-13 UNC-2A to 85 ft-lbs minimum depending upon surface conditions
  • Torque M12 x 1.75-6g to 75 ft-lbs minimum depending upon surface conditions

Finish

  • Zinc plated with clear chromate

Caution: TriMark striker bolts are designed and tested to meet or exceed FMVSS 206 (ECE R11) safety requirements only when used with TriMark's corresponding FMVSS 206 (ECE R11) compliant latches. Note that some of the longer striker bolts have diminished load values in certain latch families. Please check with TriMark Engineering before finalizing your striker selection requiring FMVSS 206 (ECE R11) compliance.

Latch & Striker Installation

  • Install striker bolt in door frame
  • Close door carefully and check for interference between head of striker bolt and latch components
  • Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
  • Adjust striker bolt vertically so door is not guided upward or downward while being closed
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust striker bolt
  • After installation, check door alignment and door seal pressures

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-0200 .675" (17.1mm) Diameter Striker Bolt and Optional Guard

Please specify search criteria:


CompareCatalog NumberTriMark NumberShoulder DiameterThread SizeInstalled LengthThread LengthDrive Detail Internal or ExternalWasher Dia. X ThicknessStriker GuardTypePackagingStatus CodeSample RequestCAD Drawing
0700200-00-00-000-0000-00-00-00000-08-113951-01 NA None NA NA NA NA No Plate, offset left 1.39", (2) .51" holes, 2.4" X 1.99", zinc plated Standard A/CP
0700200-00-00-086-0000-00-00-14109.01-06-114109-01 NA None 0.86 NA NA NA Guard, offset right, zinc plated, 1.225" Guard Standard A/CP
0700200-00-00-091-0000-00-00-81623.12-06-581623-12 NA None 0.91 NA NA NA Guard, non-handed, medium gloss black, 1.25" X 1.228" Guard Bagged and boxedA/A
0700200-00-00-091-0000-00-00-81623.16-06-581623-16 NA None 0.91 NA NA NA Guard, non-handed, zinc plated, 1.25" X 1.228" Guard Bagged and boxedA/A
0700200-00-00-100-0000-00-00-29918.01-06-129918-01 NA None 1 NA NA NA Guard, non-handed, zinc plated, 1.26" X 1.23" Guard StandardA/A
0700200-00-00-123-0000-00-00-20338.01-06-120338-01 NA None 1.23 NA NA NA Guard, non-handed, zinc plated, 31.76mm X 31.2mm Guard StandardA/A
0700200-06-00-163-0000-13-00-21232.01-12-120964-01 0.675 None 1.63 NA Welded on Plate NA Guard, non-handed, zinc plated, .79" X 1.245" Bolt fastened to 20963-01 plate, (2) 13.5mm X 11.35mm slots, 25mm X 40mm StandardA/A
0700200-06-00-197-0000-13-00-00000-04-121227-01 0.675 None 1.97 NA Welded on Plate NA No Bolt fastened to 21262-01 plate, (2) 13.63mm holes, 60mm X 30mm, offset right 40mm StandardA/A
0700200-06-00-222-0000-13-00-00000-10-120472-01 0.675 None 2.22 NA Welded on Plate NA No Bolt fastened to 20990-01 plate, (2) 8.9mm X 11.1mm slots, 80.4mm X 40mm, offset right 26.4mm StandardA/A
0700200-06-00-222-0000-13-00-00000-13-120989-01 0.675 None 2.22 NA Welded on Plate NA No Bolt fastened to 20990-01 plate, (2) 8.9mm X 11.1mm slots, 80.4mm X 40mm, offset left 26.4mm StandardA/A
0700200-06-01-085-0865-06-00-00000-02-180600-16 0.675 7/16-14 UNC-2A 0.85 0.865 0.750 External NA No Bolt StandardA/A
0700200-06-01-098-0731-06-09-00000-01-110795-16 0.675 7/16-14 UNC-2A 0.98 0.731 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-098-0731-06-09-00000-01-210795-16-BX00 0.675 7/16-14 UNC-2A 0.98 0.731 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring Special, 135 pieces per boxA/A
0700200-06-01-098-0731-06-09-00000-09-110795-01 0.675 7/16-14 UNC-2A 0.98 0.731 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring, black coated bolt StandardA/A
0700200-06-01-098-0929-06-09-00000-01-121051-01 0.675 7/16-14 UNC-2A 0.98 0.929 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-115-0875-06-00-00000-02-110645-16 0.675 7/16-14 UNC-2A 1.15 0.875 0.750 External NA No Bolt StandardA/A
0700200-06-01-117-0731-06-09-00000-01-110339-16 0.675 7/16-14 UNC-2A 1.17 0.731 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-117-1106-06-09-00000-01-132275-01 0.675 7/16-14 UNC-2A 1.17 1.106 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-117-1106-06-15-00000-01-124036-01 0.675 7/16-14 UNC-2A 1.17 1.106 0.750 External 1.50 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-119-0715-06-11-00000-01-110339-01 0.675 7/16-14 UNC-2A 1.19 0.715 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-01-128-0741-04-09-00000-01-119812-01 0.675 7/16-14 UNC-2A 1.28 0.741 0.312 Internal 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-128-0741-06-09-00000-01-110646-16 0.675 7/16-14 UNC-2A 1.28 0.741 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-135-0865-06-00-00000-02-110092-16 0.675 7/16-14 UNC-2A 1.35 0.865 0.750 External NA No Bolt StandardA/A
0700200-06-01-144-0606-04-11-00000-01-115986-01 0.675 7/16-14 UNC-2A 1.44 0.606 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-01-148-0731-06-09-00000-01-110338-16 0.675 7/16-14 UNC-2A 1.48 0.731 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-01-170-1050-06-09-00000-01-111050-15 0.675 7/16-14 UNC-2A 1.70 1.05 0.750 External 1.10 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-02-120-0850-06-11-00000-01-110722-16 0.675 1/2-13 UNC-2A 1.2 0.85 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-02-120-0850-06-11-00000-01-210722-16-BX00 0.675 1/2-13 UNC-2A 1.2 0.85 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special, 135 pieces per boxA/A
0700200-06-02-157-0795-06-11-00000-01-112474-16 0.675 1/2-13 UNC-2A 1.57 0.795 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-04-100-0000-01-00-00000-02-114108-01 0.675 3/8-16 UNC-2B 1 NA 6mm Internal NA No Bolt StandardA/A
0700200-06-04-120-0000-07-00-00000-02-181389-16 0.675 3/8-16 UNC-2B 1.2 NA 0.875 External NA No Bolt StandardA/A
0700200-06-04-150-0000-07-00-15666.01-11-120775-01 0.675 3/8-16 UNC-2B 1.5 NA 0.875 External NA Guard, non-handed, zinc plated, 1.024" X 1.228" Bolt fastened to 20773-01 plate, (2) 14mm holes, 0 X 60mm StandardA/A
0700200-06-06-085-0882-06-00-00000-02-180902-16 0.675 M12 X 1.75-6g 0.85 0.882 0.750 External NA No Bolt StandardA/A
0700200-06-06-085-1120-06-00-00000-01-130181-01 0.675 M12 X 1.75-6g 0.85 1.12 0.750 External NA No Bolt, washer, o-ring StandardA/A
0700200-06-06-089-0708-04-00-00000-01-136799-01 0.675 M12 X 1.75-6g 0.89 0.708 0.312 Internal NA No Bolt, washer, o-ring StandardA/A
0700200-06-06-100-0732-06-10-00000-01-117759-01 0.675 M12 X 1.75-6g 1 0.732 0.750 External 1.10 X 0.15 No Bolt, washer, o-ring StandardA/A
0700200-06-06-100-0732-06-11-00000-01-111111-16 0.675 M12 X 1.75-6g 1 0.732 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-100-0732-06-11-00000-01-311111-16-BX00 0.675 M12 X 1.75-6g 1 0.732 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring Special, 50 pieces per boxA/A
0700200-06-06-100-0890-06-11-00000-01-119171-01 0.675 M12 X 1.75-6g 1 0.89 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-108-0891-04-15-00000-01-129768-01 0.675 M12 X 1.75-6g 1.08 0.891 0.312 Internal 1.50 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-06-112-0758-07-00-00000-02-119378-01 0.675 M12 X 1.75-6g 1.12 0.758 0.875 External NA No Bolt StandardA/A
0700200-06-06-113-0843-08-00-81623.16-01-135433-01 0.675 M12 X 1.75-6g 1.13 0.843 8mm Internal NA Guard, non-handed, zinc plated, 1.25" X 1.228" Bolt, washer, o-ring StandardA/A
0700200-06-06-124-0508-07-00-00000-02-121165-01 0.675 M12 X 1.75-6g 1.24 0.508 0.875 External NA No Bolt StandardA/A
0700200-06-06-128-0693-08-10-81623.16-01-124821-02 0.675 M12 X 1.75-6g 1.28 0.693 8mm Internal 1.10 X 0.15 Guard, non-handed, zinc plated, 1.25" X 1.228" Bolt, washer, o-ring StandardA/A
0700200-06-06-128-0693-08-11-81623.16-01-124821-01 0.675 M12 X 1.75-6g 1.28 0.693 8mm Internal 1.10 X 0.15 Grip Teeth Guard, non-handed, zinc plated, 1.25" X 1.228" Bolt, washer, o-ring StandardA/A
0700200-06-06-133-0731-08-15-00000-01-135598-01 0.675 M12 X 1.75-6g 1.33 0.731 8mm Internal 1.50 X 0.13 No Bolt, washer, o-ring StandardA/A
0700200-06-06-134-0715-08-11-00000-01-120318-01 0.675 M12 X 1.75-6g 1.34 0.715 8mm Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-134-0991-08-11-00000-01-133777-01 0.675 M12 X 1.75-6g 1.34 0.991 8mm Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-136-0613-08-11-00000-01-122729-01 0.675 M12 X 1.75-6g 1.36 0.613 8mm Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-141-0783-04-00-29463.01-01-133382-01 0.675 M12 X 1.75-6g 1.41 0.783 0.312 Internal NA Guard, non-handed, zinc plated, 1.12" X 1.30" Bolt, washer, o-ring StandardA/A
0700200-06-06-142-0900-04-15-22760.01-01-125664-01 0.675 M12 X 1.75-6g 1.42 0.9 0.312 Internal 1.50 X 0.13 Guard, non-handed, zinc plated, 1.26" X 1.23" Bolt, washer, o-ring StandardA/A
0700200-06-06-142-0910-06-11-00000-01-120054-01 0.675 M12 X 1.75-6g 1.42 0.91 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-143-0633-04-11-22760.01-01-131524-01 0.675 M12 X 1.75-6g 1.43 0.633 0.312 Internal 1.10 X 0.15 Grip Teeth Guard, non-handed, zinc plated, 1.26" X 1.23" Bolt, washer, o-ring StandardA/A
0700200-06-06-144-0920-07-11-00000-01-118644-01 0.675 M12 X 1.75-6g 1.44 0.92 0.875 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-147-0944-08-00-00000-02-126060-01 0.675 M12 X 1.75-6g 1.47 0.944 8mm Internal NA No Bolt StandardA/A
0700200-06-06-149-0711-08-11-00000-01-117764-01 0.675 M12 X 1.75-6g 1.49 0.711 8mm Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-149-0716-06-11-00000-01-116912-01 0.675 M12 X 1.75-6g 1.49 0.716 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-156-0708-04-11-00000-01-131254-01 0.675 M12 X 1.75-6g 1.56 0.708 0.312 Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-162-0708-04-10-29463.01-01-129786-01 0.675 M12 X 1.75-6g 1.62 0.708 0.312 Internal 1.10 X 0.15 Guard, non-handed, zinc plated, 1.12" X 1.30" Bolt, washer, o-ring StandardA/A
0700200-06-06-163-0633-04-11-29463.01-01-122759-01 0.675 M12 X 1.75-6g 1.63 0.633 0.312 Internal 1.10 X 0.15 Grip Teeth Guard, non-handed, zinc plated, 1.12" X 1.30" Bolt, washer, o-ring StandardA/A
0700200-06-06-163-0633-04-11-36549.01-01-136550-01 0.675 M12 X 1.75-6g 1.63 0.633 0.312 Internal 1.10 X 0.15 Grip Teeth Guard, non-handed, zinc plated, 1.87" Bolt, washer, o-ring StandardA/A
0700200-06-06-184-0874-08-11-00000-01-150718-01 0.675 M12 X 1.75-6g 1.84 0.874 8mm Internal 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-192-0799-08-11-38497.01-01-122079-01 0.675 M12 X 1.75-6g 1.92 0.799 8mm Internal 1.10 X 0.15 Grip Teeth Guard, non-handed, zinc plated, 1.26" X 1.23" Bolt, washer, o-ring StandardA/A
0700200-06-06-197-0858-06-00-00000-02-119373-01 0.675 M12 X 1.75-6g 1.97 0.858 0.750 External NA No Bolt StandardA/A
0700200-06-06-216-0745-04-10-21634.0-01-121630-01 0.675 M12 X 1.75-6g 2.16 0.745 0.312 Internal 1.10 X 0.15 Guard, non-handed, zinc plated, 1.25" X 1.23" Bolt, washer, o-ring StandardA/A
0700200-06-06-221-0901-06-11-00000-01-115506-01 0.675 M12 X 1.75-6g 2.21 0.901 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-230-1040-06-11-00000-01-119828-01 0.675 M12 X 1.75-6g 2.30 1.04 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-06-236-0879-04-00-00000-02-132493-01 0.675 M12 X 1.75-6g 2.36 0.879 0.312 Internal NA No Bolt StandardA/A
0700200-06-06-251-0633-06-00-00000-02-122840-01 0.675 M12 X 1.75-6g 2.51 0.633 0.750 External NA No Bolt StandardA/A
0700200-06-06-295-0870-06-11-00000-01-114270-01 0.675 M12 X 1.75-6g 2.95 0.87 0.750 External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-07-137-0958-01-02-00000-01-129764-01 0.675 M10 X 1.5-6g 1.37 0.958 6mm Internal 0.79 X 0.11 No Bolt, washer, o-ring StandardA/A
0700200-06-07-144-0883-01-02-23770.01-01-123766-01 0.675 M10 X 1.5-6g 1.44 0.883 6mm Internal 0.79 X 0.11 Guard, non-handed, Aautophoretic black, 1.10" X 1.23" Bolt, washer, o-ring StandardA/A
0700200-06-07-244-0839-08-00-00000-02-135712-01 0.675 M10 X 1.5-6g 2.44 0.839 8mm Internal NA No Bolt StandardA/A
0700200-06-10-149-0696-15-11-00000-01-151292-01 0.675 M12 X 1.75-6H 1.49 0.696 19.05 mm External 1.10 X 0.15 Grip Teeth No Bolt, washer, o-ring StandardA/A
0700200-06-11-132-0689-16-00-00000-02-151801-01 0.675 M12 X 1-6G 1.32 0.689 22MM External NA No Bolt StandardA/A
0700200-06-12-223-1540-07-00-00000-02-151861-01 0.675 M16 X 2.0-6G 2.23 1.54 0.875 External NA No Bolt StandardA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale