050-0204 Slimline Latch With Inline Trip Lever

This single rotor latch is a sub-platform to the TriMark proven 050-0200 series latch and is designed for light to medium-duty applications for on or off-highway compartments and access panels. It features an inline trip mechanism for applications where it is desirable to have the release mechanism in-line with the latch.

Designed For

  • Thinner, light or medium weight door applications requiring resistance to dust and vibration
  • Door weights up to 75 lbs. (34 kg)
  • Door seal pressures of 20-25 lbs. (9-11 kg) recommended for best results. Not to exceed 50 lbs. (23 kg)
  • Visible surface installation or concealed installation
  • Applications where it is desireable to have the release mechanism in-line with the latch
  • Use with TriMark 070-0100 Striker Bolt 

Available

  • Left or right hand configurations
  • With standard .265" (6.7mm) diameter "thru" axles as shown, 1/4-20 UNC threaded axles or M6 x 1.0 threaded axles

Finish

  • Zinc plated, clear chromate steel components

Material

  • Internal latch components: Heat treated smooth edge stamped steel
  • Springs: Non-corrosive stainless steel
  • Case halves: High strength steel

Installation

  • (3) 1/4-20 UNC grade 5-type or M6 x 1 class 8.8 or better fasteners are recommended
  • Vertical mounting with support ramp at top is required for proper alignment and subsequent engagement of locking pawl and striker bolt
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)

Internal Lubrication

  • Oven-cured dry lubricant is applied on all critical moving parts
  • Additional lubrication to be applied in the field if required

Caution: Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0204 Slimline Latch With Inline Trip Lever

  • Agricultural Tractor / Combine

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Bus / Motorcoach / Mass Transit

    Access Panels

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Heavy Earthmoving

    Access Panels

    Door Hold Open

    Exterior Storage Compartments


  • Construction - Lifting and Material Handling

    Access Panels

    Engine Compartments / Hoods

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Construction - Light Earthmoving

    Access Panels

    Door Hold Open

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Heavy Truck / Sleeper Cabs

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Storage Compartments

    Tool Boxes


  • Industrial Enclosure/Cabinet

    Access Panels/Cabinet Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Replicars / Kit Cars

    Engine Compartments / Hoods

    Exterior Personnel Doors


  • Step Van / Walk-in Vans / Delivery Vehicle

    Exterior Personnel Doors

    Exterior Storage Compartments

    Sliding Doors

    Tool Boxes


  • Trailers - Ranch / Farm / Cargo / Utility

    Access Panels

    Exterior Personnel Doors

    Exterior Storage Compartments


  • Travel Trailer / 5th Wheel

    Baggage Doors

    Exterior Personnel Doors


  • Utility Bodies / Wreckers / Specialty Truck

    Exterior Storage Compartments

    Tool Boxes


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingMountingPrimary ActuationSecondary ActuationActuation FeatureStatus CodeSample RequestCAD Drawing
0500204-1-01-17445-00000-231876-01 Right Hand 1/4-20 UNC Threaded Axles Right Hand, In Line, Straight, 2x .253 Holes No Secondary Actuation Extension SpringA/A
0500204-1-01-19065-00000-219683-01 Right Hand 1/4-20 UNC Threaded Axles Left Hand, In Line,.250, .237 Holes, Offset 20 degrees No Secondary Actuation Extension SpringA/A
0500204-1-01-24391-24389-024606-01 Right Hand 1/4-20 UNC Threaded Axles Right Hand, External, Straight, 2x .237 Holes, Offset 15 degrees Right Hand, L-shaped, 2x .237 holes,Offset .74, Nose Offset 16 degree No Actuation FeatureA/A
0500204-1-04-25306-00000-225304-01 Right Hand 0.265 (6.7mm) Diameter Through Axles Right Hand, In Line, Straight, 2X 6.3mm (.248) Holes No Secondary Actuation Extension SpringA/A
0500204-1-06-13847-00000-113845-02 Right Hand M6 X 1.0 Threaded Axles Right Hand, In Line, Straight, 3x .253 Holes No Secondary Actuation Torsion SpringA/A
0500204-1-06-20049-00000-220051-01 Right Hand M6 X 1.0 Threaded Axles Right Hand, In Line, T-Shaped, 2x .240 Holes, Nose Offset 16 degrees No Secondary Actuation Extension SpringA/A
0500204-1-06-40784-00000-140785-01 Right Hand M6 X 1.0 Threaded Axles Left Hand, In Line, Straight, 2x .253 Holes No Secondary Actuation Torsion SpringA/A
0500204-2-01-19066-00000-219684-01 Left Hand 1/4-20 UNC Threaded Axles Right Hand, In Line,.250, .237 Holes, Offset 20 degrees No Secondary Actuation Extension SpringA/A
0500204-2-06-13846-00000-013844-02 Left Hand M6 X 1.0 Threaded Axles Left Hand, In Line, Straight, 3x .253 Holes No Secondary Actuation No Actuation FeatureA/A
0500204-2-06-20041-00000-220045-01 Left Hand M6 X 1.0 Threaded Axles Left Hand, Offset, T-shaped, 2x .240 Holes, Nose Offset 16 degree, Spring Assist No Secondary Actuation Extension SpringA/A
0500204-2-06-40784-00000-140786-01 Left Hand M6 X 1.0 Threaded Axles Left Hand, In Line, Straight, 2x .253 Holes No Secondary Actuation Torsion SpringA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale