050-0300 / 050-0310 Single Rotor Latch

Designed For

Most storage, compartment and access doors
Windows
Any application where finger or remote release is desired

Material

Strike, rotor and rotor catch: Heat treated, smooth edge stamped steel
Case halves: Zinc plated, mild steel components

Available

Latch is non-handed, but trip lever handing is available
Single Position and Two Position Rotors
With (2) 1/4-20 UNC, M6 x 1.0 threaded axles or .265" (6.7mm) diameter "thru" axles

Installation

(2) 1/4-20 UNC grade 5-type or M6 x 1.0 class 8.8 or better fasteners are required (not included)
Tighten to fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)

Internal Lubrication

Oven-cured dry lubricant is applied to catch and rotor

Latch & Striker Installation

Install striker bolt in door frame.
Close door carefully and check for interference between head of striker bolt and latch components.
Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer).
Adjust striker bolt vertically so door is not guided upward or downward while being closed
CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE.
Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position.
If both primary and secondary positions are not evident, readjust striker bolt.
After installation, check door alignment and door seal pressures

Caution: Latch does not meet FMVSS 206 (ECE R11) load requirements.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

	Handing :
	Mounting :
	Actuation :
	Rotor Positions :
	Lever Spring :

Compare	Catalog Number	TriMark Number	Handing	Mounting	Actuation	Rotor Positions	Lever Spring	Status Code	Sample Request	CAD Drawing
	0500300-1-04-81377-21	12225-16	Right Hand	0.265 (6.7mm) Diameter Through	Straight Finger Release, Right Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-14706-21	14382-01	Left Hand	0.265 (6.7mm) Diameter Through	Straight, Non-handed/None, 2.26 x .20 Dia Hole (57.4mm x 5.1mm), Spring Hole	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-19641-21	19668-01	Left Hand	0.265 (6.7mm) Diameter Through	L-Shaped, Non-Handed, 4.20 x 1.36 (106.7mm x 34.5mm)	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-81034-20	11419-16	Left Hand	0.265 (6.7mm) Diameter Through	Finger Release, Left Hand, 2.50 x .56 (63.5mm x 14.2mm) Form, No Holes	Two Rotor Positions	No Lever Spring	A/A
	0500300-2-04-81378-21	12226-16	Left Hand	0.265 (6.7mm) Diameter Through	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500310-1-01-81275-11	19014-01	Right Hand	1/4-20 UNC	Straight, Non-Handed, 2.26 x .19 Dia Hole (57.4mm x 4.8mm)	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-1-01-81377-11	25041-01	Right Hand	1/4-20 UNC	Straight Finger Release, Right Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-2-01-81275-11	19013-01	Left Hand	1/4-20 UNC	Straight, Non-Handed, 2.26 x .19 Dia Hole (57.4mm x 4.8mm)	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-2-01-81378-11	25042-01	Left Hand	1/4-20 UNC	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Single Rotor Position	Normal Duty Lever Spring	A/A

050-0300 / 050-0310 Single Rotor Latch

Typical Uses

050-0300 / 050-0310 Single Rotor Latch

Please specify search criteria:

9/9 result(s) match your searching criteria.

Products

Industries

Support

Contact Us

My Info

TriMark Global Sites

About Us

TriMark Corporation (USA)

TriMark Europe

TriMark China