050-0200 Slimline Rotary Latch

Designed For

Thin, light or medium weight door applications
Door weights up to 75 lbs. (34 kg)
Door seal pressures of 20-25 lbs. (9-11 kg) recommended for best results (not to exceed 50 lbs. (23 kg)
Visible surface installation or concealed installation

Available

Left or right hand configurations (left hand shown)
With standard .265" (6.7mm) diameter "thru" axles as shown, 1/4-20 UNC threaded axles or M6 x 1.0 threaded axles

Finish

Zinc plated, clear chromate steel components
Stainless steel

Material

Internal latch components: Heat treated smooth edge stamped steel
Springs: Non-corrosive stainless steel
Case halves: High strength steel

Internal Lubrication

Oven-cured dry lubricant is applied on all critical moving parts

Installation

(3) 1/4-20 UNC grade 5-type or M6 x 1 class 8.8 or better fasteners are recommended
Vertical mounting with support ramp at top is required for proper alignment and subsequent engagement of locking pawl and striker bolt
Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)
Note: In order to pass the FMVSS 206 strength requirement for this latch family, latches that contain 1/4 -20 UNC or M6 x 1.0 threaded axles must utilize fasteners that have sufficient length so that the end of the fastener passes completely through the entire axle and extend beyond the outside surface of the latch case

U.S. Patent No. 7,156,430 / 7,320,488

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Caution: Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval

	Handing :
	Mounting :
	Actuation :
	Actuation Feature :
	Front Plate :

Compare	Catalog Number	TriMark Number	Handing	Mounting	Actuation	Actuation Feature	Front Plate	Status Code	Sample Request	CAD Drawing
	0500200-1-01-1177816-00-1	14479-01	Right Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 2.44 X .90 X .24 Dia Hole (62.0mm X 22.9 X 6.1mm), Stop, Spring Hole	No Actuation Feature	Standard	A/A
	0500200-1-01-1190916-00-1	11923-16	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 2.19 X .76 (55.6mm X 19.3mm), Stop, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-1215716-00-1	12159-16	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Non-Handed, 1.56 X .16 (39.6mm X 4.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-1258301-00-1	31658-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	No Actuation Feature	Standard	A/A
	0500200-1-01-1258301-09-1	18744-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at side, .150" hole	Standard	A/A
	0500200-1-01-1258301-11-1	12586-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at side, .265" hole	Standard	A/A
	0500200-1-01-1258302-00-1	23303-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	No Actuation Feature	Standard	A/A
	0500200-1-01-1258302-03-1	24006-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	Wave Washer	Standard	A/A
	0500200-1-01-1258302-04-1	12720-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	1 Rod collar at top, .265" hole	Standard	A/A
	0500200-1-01-1338901-00-1	13426-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 1.74 X 1.11 (44.2mm X 28.2mm), Stop, Offset, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-1585601-03-1	15855-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Hand Lever, 1.15 X .72 X .25 Dia Hole (29.2mm X 18.3mm X 6.4mm), Offset	Wave Washer	Standard	A/A
	0500200-1-01-1674501-00-1	11923-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 1.74 X 1.11 (44.2mm X 28.2mm), Stop, Offset, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-1795801-00-1	17999-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 1.65 X .31 X .25 Dia Hole (41.9mm X 7.9mm X 6.4mm), Form	No Actuation Feature	Standard	A/A
	0500200-1-01-1815201-00-1	11923-02	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 1.74 X .69 (44.2mm X 17.5mm), Stop, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-1900601-00-1	19007-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Hand Actuator, 1.13 X .57 X .28 Dia Hole (28.7mm X 14.5mm X 7.1mm) Form, Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-2350501-00-1	23506-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Handed, .19 X .93 X 1.38 X .25 Dia Hole (4.8mm X 23.6mm X 35.1mm X 6.4mm), Stop, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-2430601-05-1	39014-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Right Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Yellow Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-2430602-05-1	39014-02	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Right Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Blue Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-2430603-05-1	39014-03	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Right Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, High Gloss Black Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-2463801-00-1	24639-01	Right Hand	1/4-20 UNC Threaded Axles	L-Shaped, Right Handed, 1.30 X 1.71 (33.0mm X 43.4mm), Stop, Form	No Actuation Feature	Standard	A/A
	0500200-1-01-2596701-00-1	24820-01	Right Hand	1/4-20 UNC Threaded Axles	4-Point, Non-Handed, 1.10 X 1.10 X .24 Dia Hole (27.9mm X 27.9mm X 6.1mm)	No Actuation Feature	Standard	A/A
	0500200-1-01-2675101-00-1	26757-01	Right Hand	1/4-20 UNC Threaded Axles	Finger Release, Right Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, Yellow Vinyl	No Actuation Feature	Standard	A/A
	0500200-1-01-2675102-00-1	26757-02	Right Hand	1/4-20 UNC Threaded Axles	Finger Release, Right Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, Blue Vinyl	No Actuation Feature	Standard	A/A
	0500200-1-01-2675103-00-1	26757-03	Right Hand	1/4-20 UNC Threaded Axles	Finger Release, Right Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, High Gloss Black Vinyl	No Actuation Feature	Standard	A/A
	0500200-1-01-3098301-00-1	30763-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Left Handed, .625 X 1.25 X 1.08 X .265 Dia Hole, Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-3098401-00-1	30761-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Right Handed, .625 X 1.25 X 1.08 X .265 Dia Hole, Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-3278301-00-1	32785-01	Right Hand	1/4-20 UNC Threaded Axles	2 Point, Right Handed, .63 X 1.25 X 1.08 X .230 Slot, Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-3337701-00-1	33378-01	Right Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 2.10 X 1.45 X .08 Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-3530901-05-1	35160-01	Right Hand	1/4-20 UNC Threaded Axles	1-Point, Finger, Right Handed, 1.12 X .660 X 1.395 X .203 (28.4mm X 16.8mm X 35.4mm X 5.2mm), Stop, Offset, Orange Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-3547701-07-1	35390-01	Right Hand	1/4-20 UNC Threaded Axles	2 point right handed, 1.250 x .58 x .237,(31.8mm x 14.7mm x 6.02mm), Stop,Offset, Thin nose detail for secondary release clearance	Glow in Dark secondary release	Standard	A/A
	0500200-1-01-3557801-05-1	35574-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, L Shaped, Right Handed, 1.12 X .780 X .203 (28.4mm X 19.8mm X 5.2mm), Stop, Offset	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-3634801-05-1	36350-01	Right Hand	1/4-20 UNC Threaded Axles	1-Point, Right Handed, 1.12 X .17 X .203 (28.4mm X 4.3mm X 5.2mm), Stop, Offset,	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-3777101-06-1	37759-01	Right Hand	1/4-20 UNC Threaded Axles	Right Hand, .63 Offset X 2.00 X .20 (16.0mm X 50.8mm X 5.1mm), .237 Dia Hole (6.02mm)	Dipped secondary release	Standard	A/A
	0500200-1-01-3777401-06-1	37751-01	Right Hand	1/4-20 UNC Threaded Axles	Right Handed, .63 Offset X 2.00 X .237 Diam Hole	Dipped secondary release	Standard	A/A
	0500200-1-01-3864201-05-1	38643-01	Right Hand	1/4-20 UNC Threaded Axles	1-Point, Right Handed,1.12 x .17 x .203 (28.4mm X 4.3mm x 5.2mm), Stop, Offset, Extra Clearance	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-3864601-05-1	38647-01	Right Hand	1/4-20 UNC Threaded Axles	1-Point, Right Handed,1.12 x .17 x .203 (28.4mm X 4.3mm x 5.2mm), Stop, Offset, Extra Clearance	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-1-01-3897501-01-1	38868-01	Right Hand	1/4-20 UNC Threaded Axles	Cross dimensional, Left Hand, .297 dia., Orange Vinyl, E Release	Torsion Spring	Standard	A/A
	0500200-1-01-3975001-08-1	39753-01	Right Hand	1/4-20 UNC Threaded Axles	2 Point, .237 dia, Slot, Offset	Extension Spring	Standard	A/A
	0500200-1-01-3975101-01-1	38725-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, V Shaped, Left Handed, .237, Slot,Offset	Torsion Spring	Standard	A/A
	0500200-1-01-8093401-00-1	11789-01	Right Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 1.25 X .26 Dia Hole (31.8mm X 6.6mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-8093416-00-1	11789-16	Right Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-8118502-00-1	11656-02	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9 X 31.8 X 27.4 X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-8118516-00-1	11656-16	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-01-8118516-03-1	19353-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	Wave Washer	Standard	A/A
	0500200-1-01-8118516-09-1	11656-01	Right Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	1 Rod collar at side, .150" hole	Standard	A/A
	0500200-1-04-1177816-00-1	11863-16	Right Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 2.44 X .90 X .24 Dia Hole (62.0mm X 22.9 X 6.1mm), Stop, Spring Hole	No Actuation Feature	Standard	A/A
	0500200-1-04-1258301-03-1	14230-03	Right Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	Wave Washer	Standard	A/A
	0500200-1-04-1258302-00-1	13746-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	No Actuation Feature	Standard	A/A
	0500200-1-04-1258302-03-1	14230-02	Right Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	Wave Washer	Standard	A/A
	0500200-1-04-2003101-00-1	20032-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Right Handed, 3.80 X .46 X .13 Dia Slot (96.5mm X 11.7mm X 3.3mm), Stop, Offset, Form	No Actuation Feature	Standard	A/A
	0500200-1-04-2635201-01-1	26354-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	Finger Release, Right Handed, 2.34 X .62 (59.5mm X 15.8mm), Stop	Torsion Spring	Standard	A/A
	0500200-1-04-3206301-01-1	32343-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	Offset, Right Handed, 2.0 X .157 X .230 Dia Slot (50.8mm X 3.99mm X 5.84mm), Forms	Torsion Spring	Standard	A/A
	0500200-1-04-3367301-01-1	33675-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	2 Point, Right Handed, 2.00 X .210 Dia Slot (50.8mm X 5.3mm), 1.22 X .25 X .237 Dia Hole (31mm X 6.4mm X 6mm)	Torsion Spring	Standard	A/A
	0500200-1-04-3475401-06-1	34929-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	1 Point, Rght Handed, 2.00 x .63 x .210,(50.8mm x 16mm x 5.33mm), Stop,side, Offset, Thin nose detail for secondary release clearance	Dipped secondary release	Standard	A/A
	0500200-1-04-3477501-06-1	35311-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	1 Point, Right Handed, 2.00 x .63 x .210,(50.8mm x 16mm x 5.33mm), Stop,straight, Offset, Thin nose detail for secondary release clearance	Dipped secondary release	Standard	A/A
	0500200-1-04-8093416-00-1	11189-16	Right Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-04-8093416-00-2	29806-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Narrow tab	A/A
	0500200-1-04-8118502-00-1	11665-16	Right Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9 X 31.8 X 27.4 X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-04-8118516-03-1	14230-01	Right Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	Wave Washer	Standard	A/A
	0500200-1-06-1258302-11-1	24624-01	Right Hand	M6 X 1.0 Threaded Axles	2-Point, Right Hand Lever, .63 X 1.25 X 1.08 X .27 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.9mm) Stop, Offset	1 Rod collar at side, .265" hole	Standard	A/A
	0500200-1-06-3393301-01-1	33892-01	Right Hand	M6 X 1.0 Threaded Axles	U-Shaped,Right Hand,.335 Dia Hole	Torsion Spring	Standard	A/A
	0500200-1-06-5114701-00-1	51149-01	Right Hand	M6 X 1.0 Threaded Axles	L-shaped, Right Hand, 1.32 x 1.06 x .25,(33.6mm x 27mm x 6.35mm), Offset	No Actuation Feature	Standard	A/A
	0500200-1-06-8093416-00-1	24907-01	Right Hand	M6 X 1.0 Threaded Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-1-06-8118516-00-1	19276-01	Right Hand	M6 X 1.0 Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-1177816-00-1	15800-01	Left Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 2.44 X .90 X .24 Dia Hole (62.0mm X 22.9 X 6.1mm), Stop, Spring Hole	No Actuation Feature	Standard	A/A
	0500200-2-01-1258401-00-1	23304-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	No Actuation Feature	Standard	A/A
	0500200-2-01-1258401-03-1	24007-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	Wave Washer	Standard	A/A
	0500200-2-01-1258401-04-1	12719-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at top, .265" hole	Standard	A/A
	0500200-2-01-1258401-09-1	18745-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at side, .150" hole	Standard	A/A
	0500200-2-01-1258401-11-1	12585-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at side, .265" hole	Standard	A/A
	0500200-2-01-1424701-03-1	14265-01	Left Hand	1/4-20 UNC Threaded Axles	L-Shaped, Left Hand Lever, 1.94 X .68 X .25 Dia Hole (49.3mm X 17.3mm X 6.4mm) Offset, Stop	Wave Washer	Standard	A/A
	0500200-2-01-2430301-03-1	24301-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Left Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Yellow Vinyl	Wave Washer	Standard	A/A
	0500200-2-01-2430302-03-1	24301-02	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Left Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Blue Vinyl	Wave Washer	Standard	A/A
	0500200-2-01-2430302-05-1	39013-02	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Left Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Blue Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-2430303-00-1	24301-03	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Left Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, High Gloss Black Vinyl	No Actuation Feature	Standard	A/A
	0500200-2-01-2430303-05-1	39013-03	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Left Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, High Gloss Black Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-2430601-05-1	39013-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Finger, Right Handed, 1.8 X 1.71 X 1.45 X 1.0 (45.7mm X 43.4mm X 36.8mm X 25.4mm), Stop, Form, Yellow Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-2489301-03-1	24894-01	Left Hand	1/4-20 UNC Threaded Axles	U-Shaped,LH,.333x1.46x.72x.250 Dia hole x.28 Offset,8.458x37.084x18.288x6.35 Dia hole x 6.35 offset	Wave Washer	Standard	A/A
	0500200-2-01-2501601-00-1	25015-01	Left Hand	1/4-20 UNC Threaded Axles	L-Shaped, Left Handed, .56 (14.2mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-2596701-00-1	24819-01	Left Hand	1/4-20 UNC Threaded Axles	4-Point, Non-Handed, 1.10 X 1.10 X .24 Dia Hole (27.9mm X 27.9mm X 6.1mm)	No Actuation Feature	Standard	A/A
	0500200-2-01-2675001-00-1	26756-01	Left Hand	1/4-20 UNC Threaded Axles	Finger Release, Left Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, Yellow Vinyl	No Actuation Feature	Standard	A/A
	0500200-2-01-2675002-00-1	26756-02	Left Hand	1/4-20 UNC Threaded Axles	Finger Release, Left Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, Blue Vinyl	No Actuation Feature	Standard	A/A
	0500200-2-01-2675003-00-1	26756-03	Left Hand	1/4-20 UNC Threaded Axles	Finger Release, Left Handed, 1.81 X 1.09 X 1.03 X 1.45 (46.0mm X 27.7mm X 26.2mm X 36.8mm), Stop, High Gloss Black Vinyl	No Actuation Feature	Standard	A/A
	0500200-2-01-3098301-00-1	30764-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Left Handed, .625 X 1.25 X 1.08 X .265 Dia Hole, Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-3098401-00-1	30762-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Right Handed, .625 X 1.25 X 1.08 X .265 Dia Hole, Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-3278401-00-1	32786-01	Left Hand	1/4-20 UNC Threaded Axles	2 Point, Left Handed, .63 X 1.25 X 1.08 X .230 Slot, Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-3522801-05-1	35161-01	Left Hand	1/4-20 UNC Threaded Axles	1-Point, Finger, Left Handed, 1.12 X .660 X 1.395 X .203 (28.4mm X 16.8mm X 35.4mm X 5.2mm), Stop, Offset, Orange Vinyl	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-3547601-07-1	35391-01	Left Hand	1/4-20 UNC Threaded Axles	2 point left handed,1.250 x .58 x .237,(31.8mm x 14.7mm x 6.02mm), Stop,Offset, Thin nose detail for secondary release clearance	Glow in Dark secondary release	Standard	A/A
	0500200-2-01-3547801-01-1	41159-01	Left Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 1.34 X .95 X .196 Dia Hole (34.0mm X 24.1 X 5.0mm), Stop	Torsion Spring	Standard	A/A
	0500200-2-01-3557901-05-1	35575-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, L Shaped, Left Handed, 1.12 X .780 X .203 (28.4mm X 19.8mm X 5.2mm), Stop, Offset	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-3634701-05-1	36349-01	Left Hand	1/4-20 UNC Threaded Axles	1-Point, Left Handed, 1.12 X .17 X .203 (28.4mm X 4.3mm X 5.2mm), Stop, Offset,	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-3676401-00-1	31659-01	Left Hand	1/4-20 UNC Threaded Axles	LEVER,TRIP,OFFSET,.237" HOLES	No Actuation Feature	Standard	A/A
	0500200-2-01-3683101-00-1	11788-01	Left Hand	1/4-20 UNC Threaded Axles	LEVER,TRIP,.26 HOLE	No Actuation Feature	Standard	A/A
	0500200-2-01-3777201-06-1	37758-01	Left Hand	1/4-20 UNC Threaded Axles	.63 Offset X 2.00 X .20 (16.0mm X 50.8mm X 5.1mm), .237 Dia Hole (6.02mm)	Dipped secondary release	Standard	A/A
	0500200-2-01-3777301-06-1	37753-01	Left Hand	1/4-20 UNC Threaded Axles	Left Handed, .63 Offset X 2.00 X .237 Diam Hole	Dipped secondary release	Standard	A/A
	0500200-2-01-3864001-05-1	38641-01	Left Hand	1/4-20 UNC Threaded Axles	1-Point, Left Handed,1.12 x .17 x .203 (28.4mm X 4.3mm x 5.2mm), Stop, Offset, Extra Clearance	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-3864401-05-1	38645-01	Left Hand	1/4-20 UNC Threaded Axles	1-Point, Finger, Left Handed,1.12 x .17 x 1.395 x .203 (28.4mm X 4.3mm x 35.4mm x 5.2mm), Stop, Offset, Orange Vinyl, Extra Clearance	Friction Reducing Bushing and Washer	Standard	A/A
	0500200-2-01-3897501-01-1	38866-01	Left Hand	1/4-20 UNC Threaded Axles	Cross dimensional, Left Hand, .297 dia., Orange Vinyl, E Release	Torsion Spring	Standard	A/A
	0500200-2-01-3921801-01-1	38943-01	Left Hand	1/4-20 UNC Threaded Axles	Cross Dimensional, .237 dia, E Release	Torsion Spring	Standard	A/A
	0500200-2-01-4005501-01-1	40054-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, V Shaped, Right Handed, .237, Slot,Offset	Torsion Spring	Standard	A/A
	0500200-2-01-8093401-00-1	11788-16	Left Hand	1/4-20 UNC Threaded Axles	Straight, Non-Handed, 1.25 X .26 Dia Hole (31.8mm X 6.6mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-8118502-00-1	11657-02	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9 X 31.8 X 27.4 X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-8118516-00-1	11657-16	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-01-8118516-03-1	19352-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	Wave Washer	Standard	A/A
	0500200-2-01-8118516-12-1	11657-01	Left Hand	1/4-20 UNC Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	1 Rod collar at top, .150" hole	Standard	A/A
	0500200-2-04-1177816-00-1	11866-16	Left Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 2.44 X .90 X .24 Dia Hole (62.0mm X 22.9 X 6.1mm), Stop, Spring Hole	No Actuation Feature	Standard	A/A
	0500200-2-04-1258401-00-1	13737-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	No Actuation Feature	Standard	A/A
	0500200-2-04-1258401-03-1	14229-02	Left Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	Wave Washer	Standard	A/A
	0500200-2-04-1258401-10-1	15544-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	2 Rod Collars, .265" holes	Standard	A/A
	0500200-2-04-1417201-03-1	14435-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Left Hand Lever, 1.10 X .28 Dia Hole (27.9mm X 7.1mm) Offset, Stop	Wave Washer	Standard	A/A
	0500200-2-04-2002101-01-1	20022-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Left Handed, 3.80 X .46 X .13 Dia Slot (96.5mm X 11.7mm X 3.3mm), Stop, Offset, Form	Torsion Spring	Standard	A/A
	0500200-2-04-2635301-01-1	26355-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	Finger Release, Left Handed, 2.34 X .62 (59.5mm X 15.8mm), Stop	Torsion Spring	Standard	A/A
	0500200-2-04-3206401-01-1	32344-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	Offset, Left Handed, 2.0 X .157 X .230 Dia Slot (50.8mm X 3.99mm X 5.84mm), Forms	Torsion Spring	Standard	A/A
	0500200-2-04-3367401-01-1	33676-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	2 Point, Left Handed, 2.00 X .210 Dia Slot (50.8mm X 5.3mm), 1.22 X .25 X .237 Dia Hole (31mm X 6.4mm X 6mm)	Torsion Spring	Standard	A/A
	0500200-2-04-3475501-06-1	34928-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	1 Point, Left Handed, 2.00 x .63 x .210,(50.8mm x 16mm x 5.33mm), Stop, side, Offset, Thin nose detail for secondary release clearance	Dipped secondary release	Standard	A/A
	0500200-2-04-3475601-06-1	35312-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	1 Point, Left Handed, 2.00 x .63 x .210,(50.8mm x 16mm x 5.33mm), Stop,straight,Offset, Thin nose detail for secondary release clearance	Dipped secondary release	Standard	A/A
	0500200-2-04-3676401-03-1	14229-03	Left Hand	0.265 (6.7mm) Diameter Through Axles	LEVER,TRIP,OFFSET,.237" HOLES	Wave Washer	Standard	A/A
	0500200-2-04-8093416-00-1	11190-16	Left Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-04-8093416-00-2	29807-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Narrow tab	A/A
	0500200-2-04-8118502-00-1	11664-16	Left Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9 X 31.8 X 27.4 X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-04-8118516-03-1	14229-01	Left Hand	0.265 (6.7mm) Diameter Through Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	Wave Washer	Standard	A/A
	0500200-2-06-1258401-11-1	24623-01	Left Hand	M6 X 1.0 Threaded Axles	2-Point, Left Hand Lever, .63 X 1.25 X 1.08 X .24 Dia Hole (15.9mm X 31.8mm X 27.4mm X 6.1mm) Stop, Offset	1 Rod collar at side, .265" hole	Standard	A/A
	0500200-2-06-3393701-01-1	33893-01	Left Hand	M6 X 1.0 Threaded Axles	U-Shaped,Left Hand,.335 Dia Hole	Torsion Spring	Standard	A/A
	0500200-2-06-5114601-00-1	51148-01	Left Hand	M6 X 1.0 Threaded Axles	L-Shaped, Left Hand, 1.32 x 1.06 x .25, (33.6mm x 27mm x 6.35mm),Offset	No Actuation Feature	Standard	A/A
	0500200-2-06-8093416-00-1	24908-01	Left Hand	M6 X 1.0 Threaded Axles	Straight, Non-Handed, 1.25 X .24 Dia Hole (31.8mm X 6.1mm), Stop	No Actuation Feature	Standard	A/A
	0500200-2-06-8118516-00-1	19275-01	Left Hand	M6 X 1.0 Threaded Axles	2-Point, Non-Handed, .63 X 1.25 X 1.08 X .25 Dia Hole (15.9 X 31.8 X 27.4 X 6.4mm), Stop	No Actuation Feature	Standard	A/A

Typical Uses

050-0200 Slimline Rotary Latch

Please specify search criteria:

126/126 result(s) match your searching criteria.

Products

Industries

Support

Contact Us

My Info

TriMark Global Sites

About Us

TriMark Corporation (USA)

TriMark Europe

TriMark China