070-1000 8mm Hoop Strike

The 070-1000 8mm Hoop Strike is designed as a companion part for use with TriMark's single rotor latches that requires an 8mm diameter strike and compliance to FMVSS 206 (ECE R11).

Features/Benefits

Automotive style hoop-type strike features low profile and minimizes clothing snag hazard
Base mounted style provides a rigid base for strike support
Welded construction and heat treat exceeds FMVSS 206 (ECE R11) loads

Available

43mm high x 57mm long base
Other versions available; please inquire
Backer mount plate is available to facilitate strike mounting and adjustability (Part # 35285) (not included)

Material

Hoop material is medium carbon steel, heat treated for strength and long life

Installation

(2) M6 x 1 class 10.9 flat head fasteners are required (not included)
Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 135 in-lbs (15.0 N-m)
It is recommended that the hoop strike is mounted to the aperture with the TriMark Backer Mount Plate corresponding to hoop strike (Part # 35285) (not included)
Note: Aligning the latch and the hoop strike is KEY to proper latch function

Finish

Zinc plated with clear chromate
Black e-coat

Latch & Hoop Strike Installation

Install hoop strike in door frame (it is recommended to use TriMark Backer Mount Plate on the inside of the door jamb to facilitate mounting and adjustability - Part # 35285) (not included)
Close door carefully and check for interference between head of hoop strike and latch components
Adjust hoop strike vertically so door is not guided upward or downward while being closed (See AP050-1900 Application Guide)
CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position
If both primary and secondary positions are not evident, readjust hoop strike
After installation, check door alignment and door seal pressures

Note: TriMark hoop strikes are designed and tested to meet or exceed FMVSS 206 (ECE R11) safety requirements only when used with TriMark's corresponding FMVSS 206 (ECE R11) compliant latches.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

050-1900 Application Guide

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-1000 8mm Hoop Strike

Please specify search criteria:

	Finish :
	Height :
	Length :
	Hoop Opening :
	Mounting :

Compare	Catalog Number	TriMark Number	Finish	Height	Length	Hoop Opening	Mounting	Status Code	Sample Request	CAD Drawing
	0701000-015-00-04-00-05-1	35285-01	Zinc Plate/Clear Chromate	NA, backer mount plate	50mm, backer mount plate	NA, backer mount plate	Backer plate, (2) M6x1-6H holes, 36mm	A/A
	0701000-015-00-04-00-05-2	51736-01	Zinc Plate/Clear Chromate	NA, backer mount plate	50mm, backer mount plate	NA, backer mount plate	Backer plate, (2) M6x1-6H holes, 36mm	A/A
	0701000-015-00-05-00-06-1	36948-01	Zinc Plate/Clear Chromate	NA, backer mount plate	52mm, backer mount plate	NA, backer mount plate	Backer plate, (4) M6X1-6H holes, 36mm X 52mm X 23mm, backer plate	A/A
	0701000-015-01-01-02-02-2	35284-02	Zinc Plate/Clear Chromate	43mm	57mm	18.95mm, 9.35mm offset	(2) 6.5mm diameter holes, 13mm X 36mm	A/A
	0701000-015-02-02-01-01-2	34119-02	Zinc Plate/Clear Chromate	47mm	69mm	28.6mm, 9.35mm offset	(2) 6.5mm diameter holes, 16mm X 36mm	A/A
	0701000-087-01-01-02-02-1	37434-01	Black E-coat	43mm	57mm	18.95mm, 9.35mm offset	(2) 6.5mm diameter holes, 13mm X 36mm	A/A
	0701000-087-02-02-01-01-2	37435-02	Black E-coat	47mm	69mm	28.6mm, 9.35mm offset	(2) 6.5mm diameter holes, 16mm X 36mm	A/A