050-0500 Single Rotor Mini Latch

Designed for small compartment and access doors where low cost slam action latching is desired. It features a single or two position compact rotary and is available in a variety of trip levers and mounting axles for ease of mounting and applications

Designed For

  • Storage and compartment doors 
  • Pickup box lids and cross bed tool boxes
  • Light weight door applications
  • RV baggage doors
  • Door closing forces of 15-20 lbs. (6.8-9 kg) recommended for best results. (not to exceed 50 lbs. (23 kg)
  • Release efforts are approximately proportional to door closing forces 

Features/Benefits

  • Compact size
  • Low cost
  • Single position rotary style latching action
  • Double position also available

Available

  • Right and left hand configurations (right hand shown)
  • With (2) 1/4-20 UNC threaded axles
  • Base mount
  • With rod collars attached

Material

  • Internal latch components and case halves: High-strength steel
  • Springs: Non-corrosive stainless steel

Finish

  • Zinc plated, clear chromate
  • Stainless steel

Installation

  • (2) 1/4-20 UNC mounting fasteners (not included)
  • Custom mounting brackets and release levers upon request
  • Tighten to the manufacturers' recommended torque value, however, do not exceed 100 in-lbs. (11.2 N-m)

Caution: Latch does not meet FMVSS 206 (ECE R11) load requirements.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0500 Single Rotor Mini Latch

  • Agricultural Tractor / Combine

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Bus / Motorcoach / Mass Transit

    Access Panels

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Construction - Heavy Earthmoving

    Engine Compartments / Hoods


  • Construction - Lifting and Material Handling

    Access Panels

    Exterior Storage Compartments


  • Construction - Light Earthmoving

    Access Panels

    Engine Compartments / Hoods

    Exterior Storage Compartments


  • Fire / Rescue / Ambulance / Emergency Vehicle

    Access Panels

    Exterior Storage Compartments


  • Heavy Truck / Sleeper Cabs

    Baggage Doors

    Engine Compartments / Hoods

    Exterior Storage Compartments

    Tool Boxes


  • Industrial Enclosure/Cabinet

    Access Panels/Cabinet Doors

    Exterior Storage Compartments


  • Motor Homes

    Baggage Doors

    Engine Compartments / Hoods


  • Pick-up Truck - Tool Boxes / Topper / Tonneau

    Tool Boxes

    Topper / Tonneau


  • Step Van / Walk-in Vans / Delivery Vehicle

    Exterior Storage Compartments

    Tool Boxes


  • Trailers - Ranch / Farm / Cargo / Utility

    Access Panels

    Exterior Storage Compartments

    Interior Compartments


  • Travel Trailer / 5th Wheel

    Baggage Doors


  • Utility Bodies / Wreckers / Specialty Truck

    Exterior Storage Compartments

    Tool Boxes


Please specify search criteria:

 

  • Handing :

 

  • Mounting :

 

  • Actuation :

 

  • Material and Finish :

 

  • Rotors :

 

  • Collars :

 

  • Rotor Spring :

CompareCatalog NumberTriMark NumberHandingMountingActuationMaterial and FinishRotorsCollarsRotor SpringStatus CodeSample RequestCAD Drawing
0500500-1-01-13384.01-015-1-0-113374-01 Right Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 4-Point, Non-Handed, .50 X .120, .237 Dia (13384-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-13384.01-015-2-0-132887-01 Right Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 4-Point, Non-Handed, .50 X .120, .237 Dia (13384-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-14711.01-015-1-0-114982-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X.237 Dia (14711-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-14974.01-015-1-0-114713-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X .237 Dia, 35 Deg (14974-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-14974.01-015-1-1-114713-02 Right Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X .237 Dia, 35 Deg (14974-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment One Collar .045" wire diameterA/A
0500500-1-01-15250.01-015-2-0-116137-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15250-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-15250.01-015-2-1-116288-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15250-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment One Collar .045" wire diameterA/A
0500500-1-01-15250.03-015-2-0-116137-03 Right Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset (15250-03) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-16387.01-015-2-0-116388-01 Right Hand 1/4-20 UNC Threaded Axles Slotted L-Shaped 1-Point, Non-Handed, 1.156 X 1.156, .203 Dia (16387-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-17796.01-015-2-1-117794-01 Right Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Right Hand Lever, 1.796 X 1.071 X .82 Offset (17796-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment One Collar .045" wire diameterA/A
0500500-1-01-17796.01-091-2-1-224550-01 Right Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Right Hand Lever, 1.796 X 1.071 X .82 Offset (17796-01) Cold Rolled Steel - Autophoretic (Black) .375" Two Position, nitrotec surface treatment One Collar .056" wire diameterA/A
0500500-1-01-20495.01-015-2-0-120496-01 Right Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Right Hand, 90 Deg, 1.16 X .53 X .203 Dia (20495-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-23097.01-015-1-0-124000-01 Right Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 1-Point, Right Hand, 1.19 X .51 Offset X .236 Dia (23097-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-24813.01-015-1-0-124815-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Non-Handed, .698 X .237 Dia (24813-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-01-26528.01-015-1-0-126529-01 Right Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, .56 X .86 X 1.48 Offset X .190 Dia Hole (26528-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-02-15250.01-015-1-0-115252-01 Right Hand 0.286 (7.3mm) Diameter Through Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15250-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-1-02-20343.01-015-1-0-120359-01 Right Hand 0.286 (7.3mm) Diameter Through Axles Conventional 1-Point, Right Hand Lever, 1.21 X .55 Offset (20343-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-13384.01-015-1-0-113776-01 Left Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 4-Point, Non-Handed, .50 X .120, .237 Dia (13384-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-13384.01-015-2-0-132888-01 Left Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 4-Point, Non-Handed, .50 X .120, .237 Dia (13384-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-14711.01-015-1-0-114981-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X.237 Dia (14711-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-14711.01-015-2-0-115160-03 Left Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X.237 Dia (14711-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-14974.01-015-1-0-114712-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 2-Point, Non-Handed, .50 X 1.12 X .237 Dia, 35 Deg (14974-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-15250.01-015-2-0-116138-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15250-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-15250.03-015-2-0-116138-03 Left Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Right Hand Lever, 0.560 X 1.000 X 0.440 Offset (15250-03) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-15251.01-015-2-1-116289-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Left Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15251-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment One Collar .045" wire diameterA/A
0500500-2-01-16387.01-015-1-0-122349-01 Left Hand 1/4-20 UNC Threaded Axles Slotted L-Shaped 1-Point, Non-Handed, 1.156 X 1.156, .203 Dia (16387-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-16387.01-015-2-0-116389-01 Left Hand 1/4-20 UNC Threaded Axles Slotted L-Shaped 1-Point, Non-Handed, 1.156 X 1.156, .203 Dia (16387-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-17797.01-091-2-1-117795-01 Left Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Left Hand Lever, 1.796 X 1.071 X .82 Offset (17797-01) Cold Rolled Steel - Autophoretic (Black) .375" Two Position, nitrotec surface treatment One Collar .045" wire diameterA/A
0500500-2-01-17797.01-091-2-1-224551-01 Left Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Left Hand Lever, 1.796 X 1.071 X .82 Offset (17797-01) Cold Rolled Steel - Autophoretic (Black) .375" Two Position, nitrotec surface treatment One Collar .056" wire diameterA/A
0500500-2-01-20494.01-015-2-0-120497-01 Left Hand 1/4-20 UNC Threaded Axles Slotted 1-Point, Left Hand, 90 Deg, 1.16 X .53 X .203 Dia (20494-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-21102.01-015-2-0-121455-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Left Hand, 1.12 X .25 Offset X .265 Dia. hole (21102-01) Cold Rolled Steel - Zinc Clear Chromate .375" Two Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-23098.01-015-1-0-124001-01 Left Hand 1/4-20 UNC Threaded Axles Conventional L-Shaped 1-Point, Left Hand, 1.19 X .51 Offset X .236 Dia (23098-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-01-24813.01-015-1-0-124814-01 Left Hand 1/4-20 UNC Threaded Axles Conventional 1-Point, Non-Handed, .698 X .237 Dia (24813-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-02-15251.01-015-1-0-115253-01 Left Hand 0.286 (7.3mm) Diameter Through Axles Conventional 1-Point, Left Hand Lever, 0.560 X 1.000 X 0.440 Offset, .234" hole (15251-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-02-17257.01-015-1-0-117256-01 Left Hand 0.286 (7.3mm) Diameter Through Axles Conventional 2-Point, Non-Handed, .79 X 1.50 X .237 Dia (17257-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
0500500-2-02-22489.01-015-1-0-122490-01 Left Hand 0.286 (7.3mm) Diameter Through Axles Conventional 1-Point, Left Hand Lever, 1.21 X .55 Offset (22489-01) Cold Rolled Steel - Zinc Clear Chromate .375" Single Position, nitrotec surface treatment None .045" wire diameterA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale