050-0150 Two Rotor Latch & Release Linkage

This two rotor latch is designed for medium to heavy-duty applications for off-highway entrance doors. It features an integrated linkage that allows for direct L-handle actuation and provides for ease of mounting and applications.

Designed For

  • Door thicknesses of 1-7/8" or greater (47.6mm)
  • Door weights of 50-200 lbs. (23-91 kg)
  • Door seal pressures of 50-150 lbs. (23-68 kg) (suggested for best results)
  • Use with TriMark 070-0200 Striker Bolt

Available

  • In left or right hand configurations (right hand shown)
  • With drive bar receiver parallel to striker bolt or rotated in 15° increments (as illustrated)

Latch & Striker Installation

  • Install striker bolt in door frame
  • Close door carefully and check for interference between head of striker bolt and latch components
  • Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
  • Adjust striker bolt vertically so door is not guided upward or downward while being closed
  • CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
  • Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position
  • If both primary and secondary positions are not evident, readjust striker bolt
  • After installation, check door alignment and door seal pressures

Installation

  • (4) 1/4-20 UNC grade 5 mounting fasteners (not included).
  • Tighten to the fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13 N-m)
  • Maximum .312" (7.9mm) diameter mounting holes

Caution: Product does not meet the locking requirements for FMVSS 206 (ECE R11).

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Caution: Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0150 Two Rotor Latch & Release Linkage

  • Agricultural Tractor / Combine

    Exterior Personnel Doors


  • Construction - Heavy Earthmoving

    Exterior Personnel Doors


  • Construction - Lifting and Material Handling

    Exterior Personnel Doors


  • Construction - Light Earthmoving

    Exterior Personnel Doors


  • Power Sports

    Exterior Personnel Doors


Please specify search criteria:


CompareCatalog NumberTriMark NumberHandingMountingDrive OrientationBracketReturn Spring ConfigurationStatus CodeSample RequestCAD Drawing
0500150-1-01-1-1-111443-16 Right Hand 1/4-20 UNC 0 Degree 2.00 Bracket On cast linkA/A
0500150-1-01-1-2-111462-16 Right Hand 1/4-20 UNC 0 Degree .775 Bracket On cast linkA/A
0500150-1-01-1-3-211459-16 Right Hand 1/4-20 UNC 0 Degree 2.00 Bracket With Remote Release .668 On stamped linkA/A
0500150-1-01-2-1-111441-16 Right Hand 1/4-20 UNC 15 Degrees 2.00 Bracket On cast linkA/A
0500150-1-01-2-2-123966-01 Right Hand 1/4-20 UNC 15 Degrees .775 Bracket On cast linkA/A
0500150-2-01-1-1-111442-16 Left Hand 1/4-20 UNC 0 Degree 2.00 Bracket On cast linkA/A
0500150-2-01-1-2-111463-16 Left Hand 1/4-20 UNC 0 Degree .775 Bracket On cast linkA/A
0500150-2-01-1-3-211749-16 Left Hand 1/4-20 UNC 0 Degree 2.00 Bracket With Remote Release .668 On stamped linkA/A
0500150-2-01-2-1-111440-16 Left Hand 1/4-20 UNC 15 Degrees 2.00 Bracket On cast linkA/A
©2024 TriMark Corporation. All rights reserved.     Privacy  •  Legal Info  •  Terms and Conditions of Sale