050-0300 / 050-0310 Single Rotor Latch

This compact single rotor latch is designed for light to medium applications for on or off highway compartment doors and access panels. It features a single or two position compact rotary and is available in a variety of trip levers and mounting axles for ease of mounting and applications

Technical Publication
Request Sample

Overview
Specification
Typical Uses
View Products
Related Products

Designed For

Most storage, compartment and access doors
Windows
Any application where finger or remote release is desired

Material

Strike, rotor and rotor catch: Heat treated, smooth edge stamped steel
Case halves: Zinc plated, mild steel components

Available

Latch is non-handed, but trip lever handing is available
Single Position and Two Position Rotors
With (2) 1/4-20 UNC, M6 x 1.0 threaded axles or .265" (6.7mm) diameter "thru" axles

Installation

(2) 1/4-20 UNC grade 5-type or M6 x 1.0 class 8.8 or better fasteners are required (not included)
Tighten to fastener manufacturers' recommended torque value, however, do not exceed 120 in-lbs. (13.3 N-m)

Internal Lubrication

Oven-cured dry lubricant is applied to catch and rotor

Latch & Striker Installation

Install striker bolt in door frame.
Close door carefully and check for interference between head of striker bolt and latch components.
Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer).
Adjust striker bolt vertically so door is not guided upward or downward while being closed
CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE.
Door should be latched but not "closed" in secondary position and latched to anticipated "closed" position with respect to adjacent surfaces in primary position.
If both primary and secondary positions are not evident, readjust striker bolt.
After installation, check door alignment and door seal pressures

Caution: Latch does not meet FMVSS 206 (ECE R11) load requirements.

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0300 / 050-0310 Single Rotor Latch

Agricultural Tractor / Combine
Access Panels
Engine Compartments / Hoods
Exterior Storage Compartments
Construction - Heavy Earthmoving
Access Panels
Exterior Storage Compartments
Interior Compartments
Construction - Lifting and Material Handling
Access Panels
Engine Compartments / Hoods
Exterior Storage Compartments
Construction - Light Earthmoving
Access Panels
Engine Compartments / Hoods
Exterior Storage Compartments
Interior Compartments
Industrial Enclosure/Cabinet
Access Panels/Cabinet Doors
Exterior Storage Compartments
Motor Homes
Engine Compartments / Hoods
Interior Compartments
Travel Trailer / 5th Wheel
Interior Compartments

Please specify search criteria:

	Handing :
	Mounting :
	Actuation :
	Rotor Positions :
	Lever Spring :

Compare	Catalog Number	TriMark Number	Handing	Mounting	Actuation	Rotor Positions	Lever Spring	Status Code	Sample Request	CAD Drawing
	0500300-1-01-00000-20	11418-16	Right Hand	1/4-20 UNC	No Actuation	Two Rotor Positions	No Lever Spring	A/A
	0500300-1-01-81377-21	12017-37	Right Hand	1/4-20 UNC	Straight Finger Release, Right Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-1-04-81377-21	12225-16	Right Hand	0.265 (6.7mm) Diameter Through	Straight Finger Release, Right Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-01-00000-20	11417-16	Left Hand	1/4-20 UNC	No Actuation	Two Rotor Positions	No Lever Spring	A/A
	0500300-2-01-81378-21	12016-37	Left Hand	1/4-20 UNC	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-00000-20	11416-16	Left Hand	0.265 (6.7mm) Diameter Through	No Actuation	Two Rotor Positions	No Lever Spring	A/A
	0500300-2-04-14706-21	14382-01	Left Hand	0.265 (6.7mm) Diameter Through	Straight, Non-handed/None, 2.26 x .20 Dia Hole (57.4mm x 5.1mm), Spring Hole	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-19641-21	19668-01	Left Hand	0.265 (6.7mm) Diameter Through	L-Shaped, Non-Handed, 4.20 x 1.36 (106.7mm x 34.5mm)	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-81034-20	11419-16	Left Hand	0.265 (6.7mm) Diameter Through	Finger Release, Left Hand, 2.50 x .56 (63.5mm x 14.2mm) Form, No Holes	Two Rotor Positions	No Lever Spring	A/A
	0500300-2-04-81215-21	11691-16	Left Hand	0.265 (6.7mm) Diameter Through	L-Shaped, Left Hand, 4.56 x 1.05 x .35 Dia Hole (115.8mm x 26.7mm x 8.9mm), Form	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-81378-21	12226-16	Left Hand	0.265 (6.7mm) Diameter Through	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Normal Duty Lever Spring	A/A
	0500300-2-04-81378-22	26961-01	Left Hand	0.265 (6.7mm) Diameter Through	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Two Rotor Positions	Heavy Duty Lever Spring	A/A
	0500310-1-01-81275-11	19014-01	Right Hand	1/4-20 UNC	Straight, Non-Handed, 2.26 x .19 Dia Hole (57.4mm x 4.8mm)	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-1-01-81377-11	25041-01	Right Hand	1/4-20 UNC	Straight Finger Release, Right Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-2-01-81275-11	19013-01	Left Hand	1/4-20 UNC	Straight, Non-Handed, 2.26 x .19 Dia Hole (57.4mm x 4.8mm)	Single Rotor Position	Normal Duty Lever Spring	A/A
	0500310-2-01-81378-11	25042-01	Left Hand	1/4-20 UNC	Straight Finger Release, Left Hand, 2.36 x .59 (59.9mm x 15.0mm) Form, No Holes	Single Rotor Position	Normal Duty Lever Spring	A/A