050-0850 TriGuard Heavy Duty Latch Module with Slam Cam Option

This heavy duty latch module is designed for medium to heavy-duty entrance and rear door applications. It features a proven single rotor latch design and high strength 8 gauge (4.2mm) front mounting plate with flange mounting.

Designed For

Medium to heavy duty doors greater than 200 lbs. (91 kg) with door seal pressures of 50-150 lbs. (23-60 kg)
Use with TriMark 070-0201 Striker Bolt

Features/Benefits

Heavy duty modular construction - survives in punishing environments
Can be used on retrofit or new surface mount vehicle construction
Heavy duty latch/striker with self-aligning "slam cam" provides rotor/cam assist to heavy doors, hinges and compensates for door sag

Available

Right or left hand configurations (right hand shown)
With slotted mounting holes to facilitate vertical adjustment
Striker with self-aligning “slam cam”
Replaceable striker alignment lift blocks
Custom configured release levers

Material

Case halves: high strength steel
Springs: Non-corrosive stainless steel

Finish

Zinc plated, clear chromate steel components

Installation

(4) M8 x 1.25 class 8.8 or better fasteners are recommended (not included)
Tighten to the manufacturers' recommended torque value

U.S. Patent No. 7,938,458

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Caution: Applications of this latch may fall within the requirements of FMVSS 206 (ECE R11) and SAE J839 safety standards. These safety related requirements are dependent on door application, e.g. front and rear hinged doors, sliding doors, or hinged upward swinging doors. The entire door hardware system must be included in the design/analysis process: latch, handle, lock mechanism, cables/rods/linkages, fasteners, hinges, etc. This ensures compatibility of all components within the hardware system. If FMVSS 206 (ECE R11) is a requirement, then all of the components within the door system must comply with strength, inertia and locking requirements as specified within the Standard. Note that this product complies with FMVSS 206 (ECE R11) when tested with approved TriMark Striker Bolts in accordance with SAE J839 and that this product meets FMVSS 206 (ECE R11) load requirements and may be used in FMVSS 206 (ECE R11) applications pending TriMark application approval.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

050-0850 TriGuard Heavy Duty Latch Module with Slam Cam Option

Armored Vehicle
Exterior Personnel Doors
Interior Personnel Doors
Rear Doors
Construction - Heavy Earthmoving
Exterior Personnel Doors
Construction - Lifting and Material Handling
Exterior Personnel Doors
Construction - Light Earthmoving
Exterior Personnel Doors
Industrial Enclosure/Cabinet
Access Panels/Cabinet Doors
Exterior Storage Compartments

Please specify search criteria:

	Handing :
	Finish :
	Mounting :
	1st Actuation :
	2nd Actuation :

Compare	Catalog Number	TriMark Number	Handing	Finish	Mounting	1st Actuation	2nd Actuation	Status Code	Sample Request	CAD Drawing
	0500850-1-015-01-23329-23330	23311-01	Right Hand	Zinc Plate/Clear Chromate	9MM Through Exterior Flange Mounting (4 holes)	L-Shaped,Non-handed,2.12 x .77 x .204 DIA hole,(53.8 mm x 19.6 mm x 5.2 mm Dia Hole)	Offset,Right Hand,10.6mm Offset,32.6mm x 0.5mm x 5.25mm Dia Hole,(.42 Offset,1.28 x .02 x .21 DIA Hole)	A/A
	0500850-1-015-02-25020-00000	25034-01	Right Hand	Zinc Plate/Clear Chromate	9MM X 15MM Through Exterior Flange Mounting (4 slots)	L-Shaped,Non-handed,1.16 x .44 x .238 DIA Hole,(29.5mm x 11.2mm x 6.0mm Dia Hole)	NA	A/A
	0500850-2-015-01-23329-23331	23312-01	Left Hand	Zinc Plate/Clear Chromate	9MM Through Exterior Flange Mounting (4 holes)	L-Shaped,Non-handed,2.12 x .77 x .204 DIA hole,(53.8 mm x 19.6 mm x 5.2 mm Dia Hole)	Offset,Left Hand,10.6mm Offset,32.6mm x 0.5mm x 5.25mm Dia Hole,(.42 Offset,1.28 x .02 x .21 DIA Hole)	A/A
	0500850-2-015-02-25020-00000	25035-01	Left Hand	Zinc Plate/Clear Chromate	9MM X 15MM Through Exterior Flange Mounting (4 slots)	L-Shaped,Non-handed,1.16 x .44 x .238 DIA Hole,(29.5mm x 11.2mm x 6.0mm Dia Hole)	NA	A/A