070-0400 12mm Diameter Striker Bolt

Designed as a companion part for use with TriMark's single rotor latches and cage nuts that requires a 12mm (.472") diameter striker bolt.

Technical Publication
Request Sample

Overview
Specification
Typical Uses
View Products
Related Products

Material

AISI 4140 steel heat treated

Installation

Torque to 35 ft-lbs (46.7 N-m) minimum depending upon surface conditions

Finish

Zinc plated with clear chromate

Caution: TriMark striker bolts are designed and tested to meet or exceed FMVSS 206 (ECE R11) safety requirements only when used with TriMark's corresponding FMVSS 206 (ECE R11) compliant latches. Note that some of the longer striker bolts have diminished load values in certain latch families. Please check with TriMark Engineering before finalizing your striker selection requiring FMVSS 206 (ECE R11) compliance.

Latch & Striker Installation

Install striker bolt in door frame
Close door carefully and check for interference between head of striker bolt and latch components
Add or remove shims under striker bolt washer as required (outside diameter of shim should be larger than outside diameter of striker bolt washer)
Adjust striker bolt vertically so door is not guided upward or downward while being closed
CHECK TO DETERMINE THAT BOTH SECONDARY AND PRIMARY LATCHING POSITIONS ARE USABLE
Door should be latched but not "closed" in secondary position with respect to adjacent surfaces in primary position
If both primary and secondary positions are not evident, readjust striker bolt
After installation, check door alignment and door seal pressures

Individual part dimensions are for reference only. Refer to individual part drawings for complete dimensions, specifications, and installation procedures. Engineering assistance and application drawings are available.

Typical Uses

Typical application use illustrations are organized by Industry/System and are intended to give the user some ideas for specifying a complete system using TriMark products.

Not all Industry/System applications have typical use illustrations. If a typical use illustration is not available for your specific application, please submit a technical product information request and a technical representative can assist you in selecting a product(s) solution for your specific application.

070-0400 12mm Diameter Striker Bolt

Please specify search criteria:

	Shoulder Diameter :
	Thread Size :
	Installed Length :
	Thread Length :
	Drive Detail Internal or External :
	Washer Dia. X Thickness :
	Striker Guard :

Compare	Catalog Number	TriMark Number	Shoulder Diameter	Thread Size	Installed Length	Thread Length	Drive Detail Internal or External	Washer Dia. X Thickness	Striker Guard	Status Code	Sample Request	CAD Drawing
	0700400-00-00-102-0000-00-00-1	22420-01	NA	None	1.02	NA	NA	NA	Yes	A/A
	0700400-00-00-142-0000-00-00-1	22421-01	NA	None	1.42	NA	NA	NA	Yes	A/A
	0700400-03-00-181-0000-00-03-2	20774-01	0.472	None	1.81	NA	NA	0.25 Thick Hoop Strike Mount Plate	Hoop Strike	A/A
	0700400-03-03-102-0638-04-00-0	16904-01	0.472		1.02	0.638	0.312 Internal	NA	No	A/A
	0700400-03-06-146-0787-06-00-0	50734-01	0.472	M12 X 1.75-6g	1.46	0.787	0.750 External	NA	No	A/A
	0700400-03-07-088-1084-09-00-0	32056-01	0.472	M10 X 1.5-6g	0.88	1.084	M10 X 1.5-6g External thread	NA	No	A/A
	0700400-03-07-098-0709-10-00-0	22418-01	0.472	M10 X 1.5-6g	0.98	0.709	0.630 external	NA	No	A/A
	0700400-03-07-117-0879-09-02-0	36707-01	0.472	M10 X 1.5-6g	1.17	0.879	M10 X 1.5-6g External thread	0.79 X 0.11	No	A/A
	0700400-03-07-138-0709-10-00-0	22419-01	0.472	M10 X 1.5-6g	1.38	0.709	0.630 external	NA	No	A/A
	0700400-03-07-148-0604-09-02-0	31364-01	0.472	M10 X 1.5-6g	1.48	0.604	M10 X 1.5-6g External thread	0.79 X 0.11	No	A/A
	0700400-03-07-158-0709-08-02-1	50995-01	0.472	M10 X 1.5-6g	1.58	0.709	8mm Internal	0.79 X 0.11	Yes	A/A